BDCOM OLT All Show Command

FAQ





Contents
  1. 1. How to enable loop detection in GPON ONU (SFU)
  2. To configure the loopback on all ONT-
  3. 2. How to enable the "telnet" in BDCOM Switch please use the following commands in config mode -
  4. 3. How to increasing the session time in OLT
  5. 4. How to configure back-up link in Switch
  6. 5. How to delete ONU from CLI mode
  7. 6. How to bind ONU with OLT from CLI mode
  8. 7. How to set an IP address to ONU (SFU) from EPON OLT
  9. For different VLAN
  10. 8. How to configure SNMP in OLT
  11. 9. How to set an IP address in ONT from GPON OLT
  12. 10. How to configure VLAN at ONU in CLI mode
  13. 11. How to do port level redundancy in GPON using with 2:N Splitter
  14. 12. How to do port level redundancy in EPON using with 2:N Splitter
  15. 13. How to control storm at EPON ONU
  16. 14. How to enable loop detection in ONU from OLT
  17. To configure the loopback on all ONU
  18. 15. How to set enable password
  19. 16. How to change Native VLAN in Switch or OLT
  20. OUTPUT
  21. 17. How to change lost time of EPON ONU ?
  22. How to Set aging time for ONU SN binding entry when ONU auto unbind, in inactive or offline?
  23. For EPON
  24. For GPON
  25. 18. How to create a limited user in OLT or Switch with a limited privilege
  26. Example -
  27. 19. How to disable EPON ONU
  28. To check the status -
  29. 20. How to disable ONT (GPON ONU)
  30. To check the status -
  31. 21. How to check optical power of ONU/ONT
  32. 22. How to reboot ONU/ONT using CLI mode
  33. For EPON ONU
  34. For GPON ONT
  35. 23. How to shutdown a LAN port of an ONU (EPON) and ONT (GPON)
  36. 24. How to control storm in EPON/GPON/Switch
  37. 25. How to check the LAN port status of ONU/ONT
  38. For EPON ONU
  39. For GPON ONT
  40. 26. How to set port security by MAC in ONU
  41. 27. How to increase the ONU bandwidth capacity to 1Gbps from OLT
  42. 28. How to see MAC address table in ONU/ONT
  43. 29. How to set ONU/ONT authentication in GPON/EPON OLT with SN or MAC
  44. GPON
  45. EPON
  46. 30. How to enable SSH in EPON/GPON and Switch
  47. 31. How to configure DHCP snooping
  48. To trust the DHCP server
  49. 32. How to set rate-limit in EPON ONU (Assign bandwidth in ONU LAN port)
  50. 33. How to set rate-limit in GPON ONT (PON port / WAN port)
  51. Step01:
  52. Step02:
  53. Step03:
  54. Step04:
  55. 34. How to set a DHCP IP in OLT
  56. Create a VLAN 100 and assign IP address
  57. Create IP pool name, IP range and then enable DHCP server
  58. 35. How to set rate limit (ingress and egress) to OLT or Switch
  59. 36. How to set NTP in OLT and Switch
  60. 37. How to implement policy-map ? (Assign bandwidth on VLAN)
  61. 38. How to configure TACACS
  62. 39. How to configure Jumbo frame in GPON ONT (Maximum size is 1996, default is 1518)
  63. Step 01: Create a profile named "mtu_jumbo"
  64. Step 02: Apply the profile "mtu_jumbo" on an ONT
  65. 40. How to enable data forwarding among ONUs under the same EPON OLT PON port
  66. 41. How to forward data among the UNI ports of ONU in EPON
  67. 42. How to access the ONU (HGU) via its WAN IP address
  68. 43. How to filter/block MAC in GPON ONU
  69. Step 01: Create a profile named "Block"
  70. Step 02: Apply the profile "Block" on the specific ONU
  71. 44. How to configure multicast in GPON HGU
  72. 45. How to check distance of the ONU from OLT
  73. For EPON
  74. For GPON
  75. 46. How to configure a template for GPON ONU
  76. Step 01: Make profile
  77. Step 02: Make a template
  78. Step 03: Apply the template on the PON port of the OLT
  79. 47. How to establish data connectivity between 2 clients in GPON ? Different ONU in same PON port
  80. Step01: Make a profile named test
  81. Step02: Apply the profile on the ONU

1. How to enable loop detection in GPON ONU (SFU)

Switch#config

Swithc_config#interface gpon0/2:1

Switch_config_gpon0/2:1#gpon onu loopback-detect protocol private

Switch_config_gpon0/2:1#gpon onu uni 1 loopback-detect enable

To configure the loopback on all ONT-

Switch#config

Switch_config#interface range gpON 0/1:1-10

Switch_config_if_range#gpon onu loopback-detect protocol private

Switch_config_if_range#gpon onu uni 1 loopback-detect enable


2. How to enable the "telnet" in BDCOM Switch please use the following commands in config mode -

Switch#config

Switch_config#aaa authentication login default local

Switch_config#aaa authentication enable default none

Switch_config#aaa authorization exec default local

3. How to increasing the session time in OLT

Switch#config

Switch_config#line ?

console -- Primary terminal line

vty -- Virtual terminal


Switch_config#line console 0

Switch_config_line#exec-timeout ?

<0-86400>

Switch_config_line#exec-timeout

NB: 0 (zero) means no time out

4. How to configure back-up link in Switch

Switch#config

Switch_config#no spanning-tree

Switch_config#backup-link-group 1backup-link-group 1

Switch_config#interface GigaEthernet 0/5

Switch_config_g0/5#backup-link-group 1 active

Switch_config_g0/6#backup-link-group 1 backup


5. How to delete ONU from CLI mode

Switch#config

Switch_config#interface epon 0/3

Switch_config_epon0/3#no epon bind-onu mac xxxx.xxxx.xxxx

Switch_config_epon0/3#exit

Switch_config#wr all

6. How to bind ONU with OLT from CLI mode

Switch#config

Switch_config#interface epon 0/3

Switch_config_epon0/3#epon bind-onu mac xxxx.xxxx.xxxx

Switch_config_epon0/3#exit

Switch_config#wr all

7. How to set an IP address to ONU (SFU) from EPON OLT

Switch#config

Switch_config#interface epON 0/5

Switch_config_epon0/5#switchport mode trunk

Switch_config_epon0/5#switchport trunk vlan-untagged none

Switch_config_epon0/5#exit

Switch_config#


Switch_config#interface epON 0/5:6

Switch_config_epon0/5:6#epon onu ctc ip address static 172.16.0.100 255.255.255.0 gateway 172.16.0.1 cvlan 1 svlan 0 priority 5


NB: Here, 172.16.0.100 is for ONU IP and gateway 172.16.0.1 is OLT IP

For different VLAN

Switch_config#interface epON 0/5:6

Switch_config_epon0/5:6#epon onu port 1 ctc vlan mode trunk 100 1518

Switch_config_epon0/5:6#epon onu ctc ip address static 172.16.0.100 255.255.255.0 gateway 172.16.0.1 cvlan 1518 svlan 0 priority 5

8. How to configure SNMP in OLT

Switch_config#snmp-server community 0 <BDCOM> RW

Switch_config#snmp-server host <172.16.2.30> <BDCOM> authentication configure snmp


NB: Here "BDCOM" is the community name and the IP 172.16.2.30 is your PC IP

9. How to set an IP address in ONT from GPON OLT

Switch#config

Switch_config#inteface gpon0/2:1

Switch_config_gpon0/2:1#gpon onu ip-host ?

<1-1> -- ONU ip-host port ID

Switch_config_gpon0/2:1#gpon onu ip-host 1 address static 172.16.0.100 255.255.255.0 172.16.0.1

10. How to configure VLAN at ONU in CLI mode

Switch#config

Switch_config#interface epON 0/5:1

Switch_config_epon0/5:1#epon onu port 1 ctc vlan mode tag 200 priority 0 [Here the example VLAN is 200]

11. How to do port level redundancy in GPON using with 2:N Splitter

Switch#

Switch_config#gpon b-psg

Switch_config#interface gpsG 0/1

Switch_config_gpsg0/1#gpon psg member active gPON 0/1 standby gPON 0/2

Switch_config_gpsg0/1#no shut

Switch_config_gpsg0/1#exit

Switch_config#exit


12. How to do port level redundancy in EPON using with 2:N Splitter

Switch#

Switch_config#epon b-psg

Switch_config#interface psG 0/1

Switch_config_psg0/1#epon psg member active ePON 0/1

Switch_config_psg0/1#epon psg member standby ePON 0/2

Switch_config_gpsg0/1#no shut

Switch_config_gpsg0/1#exit

Switch_config#exit

Switch#wr all


13. How to control storm at EPON ONU

Switch#config

Switch_config#interface epON 0/1:1

Switch_config_epon0/1:1#epon onu port 1 storm-control mode ?

1 -- limit broadcast

2 -- limit multicast

3 -- limit unknown unicast

4 -- limit all packet

Switch_config_epon0/1:1#epon onu port 1 storm-control mode 1 threshold ?

<256-100000> -- Enter part of storm suppression level(unit:kbps)

Switch_config_epon0/1:1#epon onu port 1 storm-control mode 1 threshold

14. How to enable loop detection in ONU from OLT

To configure the loopback on all ONU

Switch#config

Switch_config#interface range epON 0/1:1-13

Switch_config_if_range#epon onu all-port ctc loopback detect

Switch_config_if_range#epon onu all-port ctc notify loopback


15. How to set enable password

Switch_config#enable password 0 <password>

Switch_config#aaa authentication enable default enable

16. How to change Native VLAN in Switch or OLT

Switch#

Switch#config

Switch_config#interface gigaEthernet 0/2

Switch_config_g0/2#switchport mode trunk

Switch_config_g0/2#switchport trunk vlan-allowed 999,500,510

Switch_config_g0/2#switchport pvid 999

Switch_config_g0/2#exit

Switch_config#wr all

OUTPUT

!

interface GigaEthernet0/2

switchport trunk vlan-allowed 500,510,999

switchport mode trunk

switchport pvid 999 [Here Native VLAN is 999]

17. How to change lost time of EPON ONU ?

How to Set aging time for ONU SN binding entry when ONU auto unbind, in inactive or offline?

For EPON

Switch_config#epon onu-lost-time ?

<10-10000000> -- onu lost time value (in seconds, default is 2592000 (30days))

Switch_config#epon onu-lost-time

Switch_config#exit

Switch#clear epon lost-onu

For GPON

Switch#

Switch#config#gpon onu-auto-unbind ?

<0, 1000-1000000000> -- aging time (0 default), 0 never (sec)

18. How to create a limited user in OLT or Switch with a limited privilege

Switch_config#localauthor <group name>

Switch_config_<group name>#exec privilege default 8

Switch_config#username <username> password 0 <password> author-group <group name>

Example -

Switch_config#localauthor NOC

Switch_config_localauthor_NOC#exec privilege default 8

Switch_config#username test password 0 test321 author-group NOC

Switch#config

Switch_config#aaa authorization exec default local


Switch_config#localauthor support

Switch_config_localauthor_support#exec privilege default 5


Switch_config#username test password 0 test author-group support

Switch_config#privilege exec 5 show run

19. How to disable EPON ONU

Switch#config

Switch_config#interface epON 0/1

Switch_config_epon0/1#epon onu-blacklist mac xxxx.xxxx.xxxx

To check the status -

Switch#show epon interface epON 0/1:1 onu ctc optical-transceiver-diagnosis


20. How to disable ONT (GPON ONU)

Switch#config

Switch_config#interface gpON 0/1:1

Switch_config_gpon0/1:1#gpon onu disable

Switch_config_gpon0/1:1#exit

To check the status -

Switch#show gpon interface gpON 0/1:1 onu optical-transceiver-diagnosis

21. How to check optical power of ONU/ONT

Switch#

Switch#show epon interface epON 0/1:1 onu ctc optical-transceiver-diagnosis

================================================================

Switch#

Switch#show gpon interface gpON 0/1:1 onu optical-transceiver-diagnosis

22. How to reboot ONU/ONT using CLI mode

For EPON ONU

Switch#epon reboot onu interface epON 0/1:1

For GPON ONT

Switch#gpon reboot onu interface gpON 0/1:1

23. How to shutdown a LAN port of an ONU (EPON) and ONT (GPON)

Switch#

Switch#config

Switch_config#interface epON 0/1:2

Switch_config_epon0/1:2#epon onu port 1 ctc shutdown

Switch#

Switch#config

Switch_config_gpon0/1:2#

Switch_config_gpon0/1:2#gpon onu uni 1 shutdown

24. How to control storm in EPON/GPON/Switch

Switch#config

Switch_config#interface gigaEthernet 0/1

Switch_config_g0/1#storm-control ?

broadcast -- Broadcast address storm control

multicast -- Multicast address storm control

unicast -- Unknown-Unicast address storm control

Switch_config_g0/1#storm-control broadcast threshold ?

<1-1048575> -- Enter Integer part of storm suppression level(PPS)

25. How to check the LAN port status of ONU/ONT

For EPON ONU

Switch#show epon interface epON 0/1:1 onu port 1 state

Hardware state is Link-Up

Speed is 1000MbpsDuplex is Full-Duplex

For GPON ONT

Switch#

Switch#show gpon interface gpON 0/1:1 onu port 1 state

GPON0/1:1 uni-port 1 up 10/100/1000 BASE-T(1Gbps Full-Duplex)

26. How to set port security by MAC in ONU

Switch#

Switch#config

Switch_config_epon0/1:2#

Switch_config_epon0/1:2#switchport port-security mode dynamic

Switch_config_epon0/1:2#switchport port-security dynamic maximum ?

<1-1021> -- Configure interface maximum address

27. How to increase the ONU bandwidth capacity to 1Gbps from OLT

Switch#config

Switch_config#interface epON 0/1:1

Switch_config_epon0/1:1#epon sla downstream pir ?

<512-1000000> -- Enter peak bandwidth in units of kbps

Switch_config_epon0/1:1#epon sla downstream pir 1000000 cir ?

<1-960000> -- Enter committed bandwidth in units of kbps

Switch_config_epon0/1:1#epon sla downstream pir 1000000 cir 960000 fir ?

<0-950000> -- Enter fixed bandwidth in units of kbps

28. How to see MAC address table in ONU/ONT

Switch#show mac address-table interface epON 0/1:2

Mac Address Table (Total 1)

------------------------------------------

Vlan Mac Address Type Ports

---- ----------- ---- -----

1 1062.eb21.52b8 DYNAMIC epon0/1:2

Switch#show mac address-table interface gpON 0/1:1

Mac Address Table (Total 1)

------------------------------------------

Vlan Mac Address Type Ports

---- ----------- -------- -------

350 c025.e9aa.6c79 DYNAMIC gpon0/1:1-1

29. How to set ONU/ONT authentication in GPON/EPON OLT with SN or MAC

GPON

To set the authentication method

Switch#config

Switch_config_gpon0/1#gpon onu-authen-method sn

To check the rejected ONT

Switch#show gpon onu-rejected-information

To bind the ONT with SN authentication

Switch#config

Switch_config#interface gpON 0/1

Switch_config_gpon0/1#gpon bind-onu sn ?

XXXXXXXXXXXXXXXX -- SN(16 characters)

XXXX:XXXXXXXX -- SN(VendorID:SerialNumberOfVendor)

EPON

Switch#

Switch_config#

Switch_config#interface epON 0/1

Switch_config_epon0/1#epon onu-authen-method mac


To bind the ONT with SN authentication

Switch_config_epon0/1#epon bind-onu mac ?

<xxxx.xxxx.xxxx> -- MAC address Value

30. How to enable SSH in EPON/GPON and Switch

Switch#

Switch#config

Switch_config#ip sshd enable

31. How to configure DHCP snooping

Switch#config

Switch_config#ip dhcp-relay snooping

Switch_config#ip dhcp-relay snooping vlan 1

To trust the DHCP server

Switch#config

Switch_config#interface gigaEthernet 0/1 [The trusted server is connected from gig 0/1]

Switch_config_g0/1#dhcp snooping trust

32. How to set rate-limit in EPON ONU (Assign bandwidth in ONU LAN port)

Switch#config

Switch_config#interface epON 0/1:1

Switch_config_epon0/1:1#epon onu port 1 ctc rate-limit ?

<128-1000000> -- Configure Bandwidth(unit:kbps)

Switch_config_epon0/1:1#epon onu port 1 ctc rate-limit 100000 ?

ingress -- Configure port rate-limit ingress

egress -- Configure port rate-limit egress


33. How to set rate-limit in GPON ONT (PON port / WAN port)

Step01:

Create a profile. Let's say the profile name is 1M

Switch#config

Switch_config#gpon profile onu-tcont 1M

Step02:

Assign the bandwidth (CIR and PIR) on 1M profile

Switch_config_prof_onuTcont_1M#gpon-profile tcont-type 3 pir ?

<512-1244160> -- Max Bandwidth(kbps)

Switch_config_prof_onuTcont_1M#gpon-profile tcont-type 3 pir 1024 cir ?

<256-768> -- Assured Bandwidth(kbps)

Switch_config_prof_onuTcont_1M#gpon-profile tcont-type 3 pir 1024 cir

<256-768> -- Assured Bandwidth(kbps)

Step03:

Bind the virtual port. Let's say the virtual port name is T1M

Switch_config#gpon profile onu-tcont-virtual-port-bind T1M

Switch_config_prof_onuTcontVportBind_T25M#gpon-profile virtual-port 1 profile virtual-port-default tcont 1 profile 1M

Step04:

Apply the profile on a specific ONT (0/1:1) and rate limit

Switch_config_gpon0/1:1#gpon onu tcont-virtual-port-bind-profile T1M

Switch_config_gpon0/1:1#gpon onu virtual-port 1 downstream rate-limit ?

<1-38880>




34. How to set a DHCP IP in OLT

Create a VLAN 100 and assign IP address

Switch#config

Switch_config#interface vlAN 100

Switch_config_v100#ip address 172.16.100.1 255.255.255.0

Create IP pool name, IP range and then enable DHCP server

Switch_config#ip dhcpd pool test

Switch_config_dhcp#network 172.16.100.0 255.255.255.0

Switch_config_dhcp#range 172.16.100.2 172.16.100.254

ip dhcpd enable

35. How to set rate limit (ingress and egress) to OLT or Switch

Switch_config#interface gpON 0/2

Switch_config_gpon0/2#switchport rate-limit 5000 ?

ingress -- Config port rate-limit ingress

egress -- Config port rate-limit egress

36. How to set NTP in OLT and Switch

37. How to implement policy-map ? (Assign bandwidth on VLAN)

Switch#config

Switch_config#policy-map BW_100Mb_V100

Switch-policy-map#classify vlan 100

Switch-policy-map#action bandwidth 1600

Switch-policy-map#exit

NB: Here the name of policy map is BW_100Mb_V100

Switch_config#interface gigaEthernet 0/1

Switch_config_g0/1#qos policy BW_100Mb_V100 ?

ingress -- Config port policy map ingress

egress -- Config port policy map egress


NB: Implement the policy map on VLAN 100 in the interface of gig0/1

38. How to configure TACACS

Switch_config#aaa authentication login default group tacacs+ local

Switch_config#aaa authentication enable default none

Switch_config#aaa authorization commands 15 default group tacacs+

Switch_config#aaa authorization commands 0 default group tacacs+

Switch_config#aaa authorization exec default group tacacs+ local

Switch_config#aaa accounting commands 15 default start-stop group tacacs+

Switch_config#aaa accounting commands 0 default start-stop group tacacs+

Switch_config#aaa accounting network default start-stop group tacacs+

Switch_config#tacacs-server host 172.25.102.61

Switch_config#tacacs-server key abc123xyz

39. How to configure Jumbo frame in GPON ONT (Maximum size is 1996, default is 1518)

Step 01: Create a profile named "mtu_jumbo"

Switch#config

Switch_config#gpon profile onu-uni mtu_jumbo

Switch_config_prof_onuEth_mtu_jumbo#gpon-profile max-frame-size 1996

Step 02: Apply the profile "mtu_jumbo" on an ONT

Switch_config# interface GPON0/1:1

Switch_config_gpon0/1:1#gpon onu uni 1 uni-profile mtu_jumbo


40. How to enable data forwarding among ONUs under the same EPON OLT PON port

Switch#config

Switch_config#interface epON0/1

Switch_config_epon0/1#epon inner-onu-switch

41. How to forward data among the UNI ports of ONU in EPON

Switch#config

Switch_config#interface epON0/1:1

Switch_config_epon0/1:1#no epon onu port-protect

42. How to access the ONU (HGU) via its WAN IP address

1. Access to ONU using the IP 10.0.0.10. Then enable telnet (Diagnosis=> Telnet => enable) from HGU and save it.

2. Then login to the HGU via telnet

3. Apply the command "flash default cs" and Reboot the HGU.

4. After getting the device up; configure it and enable the telnet & telnet the HGU again.

5. Apply the command "flash set ACC_TBL.0.web 3" and "flash set ACC_TBL.0.icmp 3" and Reboot the HGU.

43. How to filter/block MAC in GPON ONU

Step 01: Create a profile named "Block"

Switch#config

Switch_config#gpon profile onu-mac-filter Block

Switch-gpon-profile#gpon-profile filtertype filter

Switch-gpon-profile#gpon-profile entry 1 address a08c.fd2a.7342

Step 02: Apply the profile "Block" on the specific ONU

Switch#config

Switch_config#interface GPON0/1:1

Switch_config_gpon0/1:1#gpon onu mac-filter-profile Block

44. How to configure multicast in GPON HGU

gpon profile onu-mcst-dynamic-group test gpon-profile entry 1 multicast-gemport 4093 gpon-profile entry 1 multicast-vlan-id 1000 gpon-profile entry 1 multicast-group-address-range 239.10.10.1!gpon profile onu-mcst-oper test id 2 gpon-profile downstream-mcst-tag strip !!interface g0/1 switchport mode trunk!interface gpon0/1switchport mode trunk!interface GPON0/1:2 gpon onu tcont-virtual-port-bind-profile tvbind-default gpon onu flow-mapping-profile flow-mapping-default gpon onu virtual-port 1 gem-port 258 gpon onu veip 1 mcst-dynamic-group-profile test gpon onu veip 1 mcst-oper-profile test !ip mcst enableip mcst querier enableip igmp-proxy enable ip mcst mrouter interface GigaEthernet0/1ip mcst mc-vlan 1000 range 239.10.10.1!vlan 1000

45. How to check distance of the ONU from OLT

For EPON

#show epon active-onu

For GPON

#show gpon interface gpON 0/1:1 onu basic-info

46. How to configure a template for GPON ONU

Step 01: Make profile

Switch#config

Switch_config#gpon profile onu-tcont T20

gpon-profile tcont-type 3 pir 20480 cir 20224

gpon profile onu-rate-limit R20

gpon-profile pir 20480 cir 20480

gpon profile onu-virtual-port VP20

gpon-profile upstream rate-limit-profile R20

gpon profile onu-tcont-virtual-port-bind TV20

gpon-profile virtual-port 1 profile VP20 tcont 1 profile T20

gpon profile onu-flow-mapping F20

gpon-profile entry 1 uni type eth-uni 1

gpon-profile entry 1 virtual-port 1

=============================================================

Switch#config

Switch_config#gpon profile onu-vlan V100

Switch-gpon-profile#gpon-profile vlan mode tag

Switch-gpon-profile#gpon-profile vlan pvid 100

Step 02: Make a template

Switch#config

Switch_config#gpon onutype-template SFU

Switch_config_onutype_SFU#gpon-onutype match ctc-onu-type SFU

Switch_config_onutype_SFU#gpon-onutype config tcont-virtual-port-bind-profile TV20

Switch_config_onutype_SFU#gpon-onutype config flow-mapping-profile F20

Switch_config_onutype_SFU#gpon-onutype config virtual-port 1 downstream rate-limit 320

Switch_config_onutype_SFU#gpon-onutype config loopback-detect protocol private

Switch_config_onutype_SFU#gpon-onutype config uni 1 vlan-profile V100

Switch_config_onutype_SFU#gpon-onutype config uni 1 loopback-detect enable

Step 03: Apply the template on the PON port of the OLT

Switch#config

Switch_config#interface GPON0/1

Switch_config_gpon0/1# gpon bind-onutype SFU precedence 1

47. How to establish data connectivity between 2 clients in GPON ? Different ONU in same PON port

Step01: Make a profile named test

Switch_config# gpon profile onu-flow-mapping test

Switch-gpon-profile#gpon-profile entry 1 uni type eth-uni all

Switch-gpon-profile#gpon-profile entry 1 virtual-port 1

Switch-gpon-profile#no gpon-profile entry 1 port-protected

Step02: Apply the profile on the ONU

Switch_config# interface GPON0/2:4

Switch_config_gpon0/2:4# gpon onu flow-mapping-profile test


NB: If it is in different PON port need to use "no switchport protected" command in PON port




Post a Comment

Previous Post Next Post